| Shop-Vac 9032800 Ridgid Replacement Cartridge Filter |  | Brand: Shop-Vac
Category: Home Improvement
List Price: $16.99
Buy New: $12.93
as of 9/9/2010 06:32 CDT details
New (14) from $12.93
Rating:  17 reviews
Sales Rank: 667
Color: white
Media: Tools & Hardware
Number Of Items: 1
Shipping Weight (lbs): 1.6
Dimensions (in): 7 x 7 x 7
MPN: 903-28-00
Model: 903-28
UPC: 026282903280
EAN: 0026282903280
Release Date: August 22, 2005
Availability: Usually ships in 1-2 business days
| |
| Features:
| • | Replacement cartridge filter designed for Rigid and Craftsman wet/dry vacuums | | • | For wet and dry use | | • | Replacement filter | | • | Fits all tanks 6 gallons on up | | • | Made in USA |
|
| Similar Items:
| |
| Editorial Reviews:
Amazon.com Product Description
The Shop-Vac replacement cartridge filter is designed for Rigid and Craftsman wet/dry vacuums. For wet and dry use, this replacement filter fits all tanks six gallons on up.
|
| Customer Reviews:
Showing reviews 1-5 of 17
 NOT SIZE IT SAYS...... September 8, 2010
Dan Briggs (CA, USA)
This is NOT 7x7, it is 7 x 8 1/2 and no center hole in the bottom plate. Be careful this doesn't fit the vacs they say it does........
This does not fit all Sears Craftsmans Shop Vacs August 30, 2010
CC
I have an older taller model shop Vac, ok ok Ill try to find the model I think I saved .. CRAFTSMAN SHOP VAC - Sears Craftsman Shop Vac(Model 113 .. 178450 7amp) .. It has a rubber seal around the edge of the bottom of the orginal filter the was suppose to keep in place, but always came off, esp since they were not supported with wire back then.
However, this came with the bottom plug (which was not listed as being included .. good mistake), using a larger washer and screw I think I can attach it to the bottom support and it will be nice and snug, I havent done it yet .. but appeared to fit size wise fine.
I gave it a four because it appears to fit snug, but is not made for this model and they should list the models it fits and does not fit .. so Im having to a bit of work to get it to fit, drill hole in orginal buttom filter support that the orginal rubber gasket fit around. So extra work would be find right size drill bit, attach to cordless drill, drill hole, take drill bit out replace with phillips tip, after finding correct size screw and washer drill it carefully on. If my tools where organized it would be much easier .. still not what I purchased. But, Im ill, so tools are all over and I do not recall where anything is .. it looks like thats the case until I get well..who knows when.
 If it fits, you must equipt! August 18, 2010
Rob R. (Boston)
Fits nicely on my rigid shop vac. I'd definitely buy it again when needed and recommend that you do the same.
Fits snug, works great July 17, 2010
Adam (Seattle, WA)
Sooner or later you're going to need a new filter for your shop vac. Mine is a Rigid, and the filter finally wore out after sucking up tons of water, dust, dirt, leaves, and basically anything that would fit up the hose. Rather than buying a new vac, I went searching around for a new filter, and found this guy. It's cheaper than getting a new vac, though mine is getting a bit old. Anyways, replacing the old filter was a snap. This filter fit like a glove, and my vac is now back in action and ready for more abuse.
Perfect Fit July 11, 2010
Mrmxwll (Rocky Mountains)
1 out of 1 found this review helpful
I have one of the old 12-gallon Ridgid Wet/Dry Vacs.
This filter fit it like a glove.
It has the holding plate fashioned in. You only need
the plastic screw cap to hold it in place.
Showing reviews 1-5 of 17
|
|
|
|
| |
